amaha windows 贴片机常见报警及解决方法1、PCB传输故障：①E0070：PCB TRANSFER ERROR Unexpected PCB is on the Conveyor PCB传输故障，额外的PCB在运输轨上意义：在运输轨上的PCB，数量超过额定的数量。②E0071：The PCB detected before transfer is not detected after transfer. Maybe there is the PCB on the edge of the moving conveyor . Set the PCB to its normal Position Manually. 传输前检测的PCB在传输后检测不到，可能在移动运输轨的边缘有PCB，用手将PCB放置在其正常的位置。意义：载入开始检测的PCB在载入后不能确认，卸出前确认的PCB在出口处检测不到，或载入卸出前不能确认的PCB 在载入卸出后被检测到。③E0072：Machine in Unable to start running because the conveyor width is not ready . The conveyor width will be changed first . Misaligment of PUSH-UP PINS or PCB on conveyor may danage machine . Assure Safety and push the [ENTER] key. 意义：因未准备运输轨宽度机器不能开始运行，运输轨宽度将先被改变，在运输轨上的PCB或上推顶针的失调可能损坏机器，确保**并按[ENTER]键。④E0073：PCB is detected on the edge of the moving conveyor. Set the PCB to its normal Position mannally. 在移动运输轨边上检测到PCB，将PCB手动放置在正常位置。意义：在移动运输轨的的连接部分，危险警告传感器检测到一块PCB。⑤E0074：PCB FIXING ERROR PCB trans-Unit, Locate-Pin or push-up-Unit does not response to command. PCB固定故障 PCB传输部件，定位针或上推部件不响应指令。意义：在PCB传输部件上的定位针传感器或上推部件，传感器不能正确响应电磁阀的状况。⑥E0078: When the PCB was transfered to fixed conveyor of PCB exit Side ,error happened for time over Maybe the PCB stoppered between fix conveyor and moving enveyor or the PCB stopped is fixed Conveyor of PCB exit side . Set the PCB to its normal position mannally. 当PCB 传送到PCB出口处边的固定运输轨时，发生超时故障，PCB 可能停在固定运输轨和移动轨之间，或PCB停在PCB出口边的固定运输轨中，用手将PCB放在正常位置。意义：当从运输轨上卸出PCB时，PCB不能到达出口传感器。⑦E0079: The PCB was not able to exit from fixed conveyor of PCB exit side . Maybe the PCB stopped on edge of fixed conveyor of PCB exit side. Set the PCB to its mormal position mannally. PCB不能从出口边的固定运输轨出来，PCB可能停在PCB出口边固定运输轨边上，手动将PCB放在正常位置。意义：PCB不能载出到下一工序。⑧E0080：Moving conveyor can’t net move, because there is the PCB on the edge of the moving conveyor . Set the PCB to its normal position mannally. 移动运输轨不能移动，因为在移动运输轨边缘有PCB ，手动将PCB放于正确位置。意义：工作台A和B之间有一块PCB ，阻碍工作台移动。⑨E0081：Fixed conveyor of PCB entrance side stopper for time over. Check whether the PCB stops in fixed conveyor of PCB extrance side . PCB入口边的固定运输轨因超时停止，检查是否有PCB停止在入口边的固定运输轨中。意义：一块PCB载入无问题，但不能运到准备位置的传感器处。⑩E0082: PCBS are found both on extrance and extrance stopper, check whether more than 1 PCBS are conveyed to the working position. 在入口处和入口挡板上发现PCBS，检查是否多过一块PCBS运送到工作位置。2、丢料故障E0075：DUMP STATION FULL Dump station is filled with components. Please remove the components manually from the dump Station then start again. 丢料站满 丢料站上元件满溢，请用手从丢料站上移走元件，然后再开始。3、元件计数停止故障：E0076：COMPONENT COUNT STOP Component counter reached to specified number, Fill the component and run again . 元件计数停止元件计数器达到规定的数目，装上元件并重新运行。Componeht data 151 元件数据Feeder Set position 21 供料器安装位置意义：测试运行期间，测试的规定数目运行后发生故障。4、托盘供料器故障① E0300: Tray unit error: The component is not placed correctly on the traverser station. If the component is on the station, Please remove it . 托盘单元故障：元件未正确放置在送料横梁的站上，如果元件留在站上，移走它。Mount data 765 贴装数据Component data 153 元件数据Station 2 站Next tray position is for the next pick sequerice (x=6, y=3) 下一托盘位置是用于下一拾取工序的(x=6, y=3?意义：托盘供料器不能将元件放置在横梁站上，如果额外的元件放在规定的横梁上，移开它。②E0301：Tray unit error: Returned component is not placed correctly on the traverser station. If the component is on the station. Please remove it 托盘部件故障，退回的元件未正确放置在横梁站上，如果在横梁站上有元件，请移开它。意义：从主机退回的元件不能正确放置在横梁站上。③E0302：Tray unit error: Returned component is not placed correctly on the traverser station . If the component is on the station,please remove it . 托盘部件故障：不能从托盘上拾取元件，托盘部件不能从下面的托盘位置拾取元件。Mount data 765 贴装数据 Component data 153 元件数据 Station 2 站Next tray position is for the next pick sequence (x=6, y=3) 下一托盘位置是用于下一拾取工序的(x=6, y=3)。 意义：不能从托盘上拾取元件。